RC2014 modular systems

Modular Z80 computers and compatible RC2014 or RCBus expansion modules. Check every module for 40-pin, 60-pin, or 80-pin signals, I/O address use, firmware, and system configuration.

Also called: RC2014 Classic, RC2014 Mini, RC2014 Pro, RC2014 Standard Bus, RC2014 Enhanced Bus, RCBus, RCBus 40-pin, RCBus 60-pin, RCBus 80-pin

At a glance

Introduced: 2014

Products listed: 58

Exact-target evidence: 0

Family/interface evidence: 58

Product types: 11

Vintage searches: 0

Directory: RC2014

Browse everything below, or filter by product type, availability, and compatibility basis. Notes explain whether evidence names an exact target, a broader family, or only the relevant bus or interface for this platform.

Showing 58 products.

StatusProductWhat it doesLinks
AvailableChecked Jul 24, 202616C550 and 16C2552 UART Module Familyby Z80 Kits

Adds one or two modern 115200-baud serial ports supported by RomWBW.

For this platform (stated family): Stock support is documented for RomWBW-based Zed and Zed Pro systems. The Twin board also has custom CP/M and Microsoft BASIC ROM options for older Pro, Micro, Mini, and Classic configurations; do not infer that broader support for the other layouts.

Current listings cover one-port and two-port layouts for Standard or Enhanced Bus. RomWBW 3.4 supports the hardware, with 0xA0 or 0xA8 used for added ports; 3.5 and later also support 0x80 and 0x88. More than four serial ports needs a custom RomWBW build.

Sources
AvailableChecked Jul 24, 202632K / 64K RAM Moduleby Z80 Kits

Adds up to the Z80's full 64K addressable RAM with selectable start address.

For this platform (stated family): Used by Pro and Classic II CP/M Upgrade systems and suitable for custom Standard or Enhanced Bus builds. Standard Bus kits include a header for PAGE signals.

Current kits are offered with 32K or 64K and Standard or Enhanced Bus headers. The listing is for the memory module only; a CP/M setup also needs the documented Pageable ROM and other core modules.

Sources
AvailableChecked Jul 24, 2026512K ROM 512K RAM Moduleby Z80 Kits

Adds banked memory for running RomWBW, CP/M, and Z-System.

For this platform (stated family): Uses only the Standard Bus signals and is compatible with all RC2014 backplanes. Exact physical replacement steps differ for Zed, Classic II, Pro, and Mini systems as documented.

The current kit is the memory configuration used by RC2014 Zed and Zed Pro. It replaces both separate ROM and RAM modules in a Classic II or Pro; a Mini can use it only after its onboard ROM and RAM chips are removed.

Sources
AvailableChecked Jul 24, 20268x8 LED Matrix Display Moduleby Shiela Dixon

Adds a directly programmed 8x8 LED display for graphics and animation.

For this platform (bus/interface): A Standard Bus module programmed by writing rows and columns at ports 0 and 2.

Current kits offer several red, blue, or white display styles, or no matrix. A diffuser is included. Other 32x32 mm, 16-pin common-cathode matrices can be used if their electrical and physical layout matches.

Sources
AvailableChecked Jul 24, 2026CH375 USB Storage Moduleby Z80 Kits

Adds bootable RomWBW storage and FAT32 file exchange on USB flash drives to supported RC2014 configurations.

For this platform (stated family): The project names RC2014 Zed, Zed Pro, and kits with the 512K ROM/512K RAM Module. Plain CP/M on RC2014 Pro or Mini II/Classic II CP/M Upgrade Kits is not supported. The circuit uses Standard Bus data, address, RD, and WR signals; no Enhanced-only signal is documented. Default ports are 0x3E/0x3F or 0x3C/0x3D, with wiring options for alternatives.

RomWBW 3.4.0 or later is required. The project recommends newer branded USB sticks of at least 1 GB because some older, smaller, or unbranded media are unreliable.

Sources
AvailableChecked Jul 24, 2026Compact Flash Module v2by Z80 Kits

Adds solid-state CompactFlash storage for CP/M or RomWBW configurations.

For this platform (stated family): For CP/M, use the documented CPU, clock, serial, Pageable ROM, 64K RAM, and suitable backplane configuration. For RomWBW, the vendor documents a CPU, clock, serial, backplane, and 512K ROM 512K RAM Module.

The fine-pitch CompactFlash socket can be supplied loose with an optional stencil or pre-soldered and tested. Standard RC2014 BASIC cannot access this storage. CP/M requires the documented Pageable ROM and 64K RAM configuration, while RomWBW uses a 512K ROM 512K RAM setup.

Sources
AvailableChecked Jul 24, 2026Digital I/O Moduleby Z80 Kits

Adds eight pushbutton inputs and eight LED outputs.

For this platform (bus/interface): The vendor says the Standard Bus design is compatible with all RC2014 kits. Set its input and output ports independently to avoid conflicts.

The current listing is a complete kit, with a bare PCB offered through the vendor's grouped PCB listing.

Sources
AvailableChecked Jul 24, 2026DS1302 Real Time Clock Moduleby Ed Brindley

Adds a battery-backed clock for timekeeping and file timestamps on supported RC2014 systems.

For this platform (stated family): The vendor recommends the module for RC2014 Zed and Zed Pro systems. RomWBW users must enable DSRTCENABLE and rebuild the ROM image. The documented default I/O address is 0xC0, selected with switches 5 and 6.

The current kit is offered with or without the DS1302 IC. A CR2032 backup battery is required but is not included.

Sources
AvailableChecked Jul 24, 2026Dual Clock and Reset Moduleby Z80 Kits

Adds selectable CPU and peripheral clock rates plus supervised power-on reset.

For this platform (stated family): Used by Pro, Zed, and Zed Pro and sold as a Classic II clock replacement. Standard Bus kits include a header for CLK2; serial baud rate changes with the selected clock unless a UART has an independent clock.

Current kits include a 7.3728 MHz single-speed version and a multispeed version. A DS1233 reset monitor holds the CPU in reset while power stabilizes and a button provides manual reset. The optional manual clock switch is not supplied.

Sources
AvailableChecked Jul 24, 2026Dual Paddle Analogue Moduleby Peacock Media

Adds two 8-bit, 0-to-5 V analogue inputs for paddles, sensors, and experiments.

For this platform (stated family): The vendor explicitly lists all RC2014 models from Micro through Zed Pro. Address options are 0xDC/0xDD, 0xAC/0xAD, 0x5C/0x5D, or 0x2C/0x2D.

The current kit includes the module parts but no paddles or other input circuits. Inputs are not tolerant of voltages above the 5 V reference or below ground; add protection when measuring an external signal. A fresh conversion may require a dummy read before reading the result.

Sources
AvailableChecked Jul 24, 2026ESP8266 Wi-Fi Moduleby Z80 Kits

Connects an RC2014 serial port to a Wi-Fi network.

For this platform (bus/interface): Sold in Standard and Enhanced Bus versions. The Standard Bus kit includes a 20-pin header for access to optional TX2 and RX2 signals when UART 2 is used.

The ESP8266 and 3.3 V regulator are surface-mount parts that the builder installs. GPIO pads, status LEDs, a small prototyping area, and FTDI programming mode are provided.

Sources
AvailableChecked Jul 25, 2026Flock Floppy and RTC Familyby Sergey Kiselev / Weird Electronics

Adds a two-drive floppy controller and DS1302 real-time clock to RC2014 and RCBus systems.

For this platform (bus/interface): Both versions require RomWBW and use fixed floppy-controller ports. Flock V2 uses the 80-pin RCBus connector but is backward-compatible with the inner 40 RC2014 pins; align it carefully. The seller recommends powering a 3.5-inch drive separately when using a 40-pin backplane.

Tindie listed the complete Flock V2 kit without an out-of-stock notice on 2026-07-25, and open build files remain available. The CR2032 battery and optional 300 Kbit/s parts are not included. The drive-power output is unfused; avoid overloading or shorting it.

Sources
AvailableChecked Jul 24, 2026LCD Driver Moduleby Z80 Kits

Connects HD44780 character displays as a readable and writable RC2014 peripheral.

For this platform (stated family): The vendor states that it works with every RC2014 computer. Address pairs are 0xDA/0xDB, 0xAA/0xAB, 0x5A/0x5B, or 0x2A/0x2B.

Current kit variants include several screen sizes or the driver alone. Contrast and backlight brightness are adjustable on the module except that the 2x8 display backlight is not adjustable.

Sources
AvailableChecked Jul 24, 2026NeoPixel Display Module Familyby Peacock Media

Drives an optional 64-pixel RGB matrix or an external addressable-LED chain.

For this platform (stated family): The Standard Bus module has examples for ROM BASIC systems including Classic II, Mini, and Micro, and for CP/M systems including Pro, Zed, and Zed Pro.

Both assembled and tested layouts are currently listed. The full-size version offers an optional 8x8 matrix and filter; the Short Board includes eight diffused pixels and headers for up to two matrices. Up to 128 pixels are documented, and third-party displays can differ in pinout and RGB byte order.

Sources
AvailableChecked Jul 24, 2026Pageable ROM Moduleby Z80 Kits

Adds flexible ROM sizing and the ability to page ROM out for a full 64K of RAM.

For this platform (stated family): Used in Pro and Classic II CP/M Upgrade configurations and sold for Standard or Enhanced Bus. A Standard Bus kit includes a separate header for PAGE signals.

Current options include a standard or ZIF socket and optional blank or programmed PROMs. The base kit excludes a ROM. A ZIF release bar can foul a nearby logic chip unless the chip is lowered, the socket is reversed, or the bar is shortened. 28C EEPROM support is described as untested.

Sources
AvailableChecked Jul 24, 2026Pi Pico MicroSD Card Moduleby Extreme Kits

Replaces the RC2014 CompactFlash storage module with microSD for CP/M 2.2.

For this platform (stated family): Designed for the storage configuration used by RC2014 Pro and the Classic II CP/M Upgrade Kit. Both Standard and Enhanced Bus variants are sold; the Standard Bus installation requires the documented /WAIT jumper.

Current kits are offered for Standard or Enhanced Bus, with the surface-mount microSD socket loose or preinstalled. The Standard Bus version needs the supplied jumper lead to connect /WAIT to the CPU module. The vendor page says RomWBW support is forthcoming, so this record only claims CP/M 2.2 support.

Sources
Sold outChecked Jul 24, 2026Quazar Graphic OLED Displayby Quazar

Adds a high-contrast 128x32-pixel green OLED display.

For this platform (stated family): The vendor explicitly states compatibility with every RC2014 kit from Micro through Zed Pro.

The vendor page currently marks the assembled and tested module out of stock.

Sources
AvailableChecked Jul 24, 2026Quazar SID Interfaceby Quazar

Connects an original or modern replacement SID module to an RC2014.

For this platform (stated family): The vendor explicitly states compatibility with every RC2014 kit from Micro through Zed Pro and identifies the interface as a Standard Bus module.

No SID is included in the base module, although the current listing offers a SwinSID option and a separate 8580 adapter. The main socket directly supports a 6581, SwinSID variants, and ARMSID; an 8580 requires the adapter.

Sources
AvailableChecked Jul 24, 2026RC2014 IDE Hard Drive Moduleby Z80 Kits

Connects 2.5-inch or 3.5-inch IDE storage to a suitably configured RC2014 through an Intel 8255 interface.

For this platform (stated family): The vendor recommends the module for RC2014 Zed, Zed Pro, or another RC2014 using the 512K ROM/512K RAM Module. A 44-pin 2.5-inch drive can use RC2014 bus power or an external 5 V supply. A 40-pin drive, DOM, or CF adapter MUST receive power through its own device connector.

The vendor states that a standard RC2014 running BASIC cannot load or save files through this module. Use its documented RomWBW or z88dk software path.

Sources
AvailableChecked Jul 24, 2026RP2040 and Pi Pico VGA Terminal Familyby Z80 Kits

Adds an 80-column VGA serial terminal with USB keyboard input, a buzzer, and microSD support to an RC2014.

For this platform (stated family): The vendor explicitly states compatibility with all RC2014 models and lists both Standard Bus and Enhanced Bus. On Enhanced Bus systems such as RC2014 Pro and Zed Pro, it can use serial Port A or Port B.

The optional SD backpack is only for the earlier Pi Pico VGA Terminal. It requires PicoTerm 1.6.0 or later, can be ordered with its surface-mount socket preinstalled, and does not include the Pi Pico itself.

Sources
Build itChecked Jul 27, 2026SC114, SC126, SC130, and SC720 Motherboardsby Small Computer Central

Combines a working Z80 or Z180 computer with RC2014-compatible expansion sockets on one buildable motherboard.

For this platform (bus/interface): SC114 and SC130 expose 40-pin RCBus-2014 or RC2014 Standard Bus sockets. SC126 and SC720 expose 80-pin RCBus sockets while retaining the 40-pin RC2014 signal subset. Check every proposed module against the exact board's bus width, I/O map, processor speed, firmware, power arrangement, and compatibility table; CPU, main-memory, clock, reset, and storage modules often conflict with functions already on the motherboard.

The official pages listed complete-kit and bare-PCB suppliers on 2026-07-27, but no assembled and tested option. Exact inventory varies by model and supplier; the Tindie seller was temporarily on a break when checked. Each board still needs assembly plus the documented power, terminal, and storage accessories.

Sources
Build itChecked Jul 24, 2026SC145 Compact Flash Moduleby Small Computer Central

Adds CompactFlash storage to an RC2014 through a simple 8-bit IDE interface.

For this platform (stated family): The maker describes SC145 as an RC2014-compatible module. It occupies fixed I/O ports 0x10 through 0x17. Keep the 40-pin connection to the CompactFlash adapter to a few inches and use the documented 5 V power link.

The project supplies a schematic, Gerbers, and build documentation, and lists kit and bare-PCB suppliers; an assembled version is not offered. The unbuffered IDE connection must remain short, not every CompactFlash card is compatible, and the maker says older cards tend to work better. Power the CompactFlash adapter directly from SC145 as documented.

Sources
Build itChecked Jul 24, 2026SC151 Paged ROM Moduleby Small Computer Central

Adds four switchable 32K banks of Flash ROM to an RC2014 system.

For this platform (stated family): Designed for RC2014 systems. ROM bank selection uses ports 0x20 through 0x23 and 0x28 through 0x2B; lower-32K paging uses 0x38 through 0x3B. The status LED uses 0x08 through 0x0B.

The project page provides firmware, a schematic, PCB files, Gerbers, and supplier links. CP/M use requires the separate SC150 Paged RAM Module. Leave the Flash write-protect jumper in its normal read-only position unless deliberately programming the ROM.

Sources
Build itChecked Jul 24, 2026SC152 Memory Moduleby Small Computer Central

Combines 128K of Flash ROM and 128K of paged RAM for RC2014 systems, including CP/M configurations.

For this platform (stated family): The maker states that SC152 is fully functional on 40-pin Standard, 60-pin Enhanced, and 80-pin extended backplanes. ROM banks use ports 0x20 through 0x23 and 0x28 through 0x2B, RAM banks use 0x30 through 0x33, and lower-32K paging uses 0x38 through 0x3B.

The project page provides firmware, a schematic, PCB files, Gerbers, and supplier links. A later SC707 design also exists, but SC152 remains documented and buildable. Keep the Flash write-protect jumper in its normal read-only position except when programming it.

Sources
Build itChecked Jul 27, 2026SC691, SC791, SC792, and SC794 Modular Computersby Small Computer Central

Builds complete RomWBW and CP/M computers from matched 40-pin or 80-pin RCBus backplanes and modules.

For this platform (bus/interface): SC691 uses the RCBus-2014 40-pin bus. SC791, SC792, and SC794 use the full 80-pin RCBus. The 80-pin backplanes accept many 40-pin and 60-pin modules, but bus signals alone do not guarantee a useful combination: check every module for duplicate CPU, memory, clock, reset, serial, or storage functions, I/O-address conflicts, processor speed, and firmware support.

The official pages listed complete-kit and bare-PCB suppliers on 2026-07-27, but no assembled and tested option. Exact inventory varies by model and supplier. A suitable power supply, storage card, USB serial adapter, terminal computer, and assembly tools may be required as specified for each model.

Sources
Build itChecked Jul 24, 2026SC703 and SC712 Power and Reset Modulesby Small Computer Central

Add supervised 5 V power, manual reset, and power-on reset to an RCBus system.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. Select SC703 for an 8 V to 15 V input or SC712 for a regulated 5 V input, and do not enable more than one bus voltage supervisor.

The projects provide schematics, Gerbers, PCB design files, and kit or bare-PCB suppliers; assembled versions are not offered. SC712 requires a regulated 4.75 V to 5.25 V input. SC703's linear regulator can run hot at higher input voltages and loads. Enable only one voltage supervisor in a system.

Sources
Build itChecked Jul 24, 2026SC704 I2C Bus Masterby Small Computer Central

Adds a software-driven I2C master interface to RC2014 and RCBus systems.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. Set JP1 to an I/O address that does not conflict with other modules; the documented default is 0x0C.

The project supplies a schematic, Gerbers, PCB design files, and links for kits and bare PCBs; an assembled version is not offered. On PCB v1.0.0, the example I2C read and write address labels are reversed: read starts at 0xA1 and write starts at 0xA0.

Sources
Build itChecked Jul 24, 2026SC705 Serial ACIA Moduleby Small Computer Central

Adds a clock-stable 68B50 serial port with TTL-level flow control.

For this platform (bus/interface): Fully supported on 60-pin RC2014 Enhanced Bus and 80-pin RCBus backplanes. The core serial port also works on the 40-pin Standard Bus, but that bus does not carry the optional TX2 and RX2 signals.

The project provides a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. The serial-header power jumper must not connect two competing 5 V sources. Multiple SC705 modules require distinct I/O addresses.

Sources
Build itChecked Jul 24, 2026SC706 Z80 CPU Moduleby Small Computer Central

Provides a modular Z80 processor with flexible clock and reset options.

For this platform (bus/interface): Fully supported on the 60-pin Enhanced Bus and 80-pin RCBus. It works on the 40-pin Standard Bus without the optional /NMI, /WAIT, /RFSH, /HALT, /BUSAK, and /BUSRQ signals. Pair it with memory such as SC707 or SC714, not the 20-bit-address SC721.

The project provides a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. PCB v1.0.0 needs a wire link across C7 when X2 is not populated. Enable only one voltage supervisor in a system.

Sources
Build itChecked Jul 24, 2026SC707 Z80 Memory Moduleby Small Computer Central

Adds 128K of Flash ROM and 128K of paged RAM for a CP/M-capable Z80 system.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. It can provide the main ROM and RAM for an SC706-based Z80 system.

The project provides Small Computer Monitor S8 firmware, a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. Observe the Flash write-protect jumper and avoid function conflicts with other system memory modules.

Sources
Build itChecked Jul 24, 2026SC708 Z80 SBC Moduleby Small Computer Central

Combines a Z80, paged RAM and Flash, clock, reset, and serial terminal on one RCBus module.

For this platform (bus/interface): Fully supported on the 60-pin Enhanced Bus and 80-pin RCBus. It works on the 40-pin Standard Bus without the optional /NMI, /WAIT, /RFSH, /HALT, /BUSAK, and /BUSRQ signals. It can also run alone when powered through its serial header.

The project provides firmware, a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. SC708 has no automatic power-on reset, so press its reset button after applying power. Avoid duplicate CPU, memory, clock, reset, or serial functions when adding it to a modular system.

Sources
Build itChecked Jul 24, 2026SC714 Z80 Memory Moduleby Small Computer Central

Adds 512K of Flash ROM and 512K of banked RAM for RomWBW and CP/M.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. The documented RomWBW RCZ80_std configuration pairs it with an SC706 CPU; do not pair it with SC730.

The project supplies RomWBW and Small Computer Monitor firmware, a schematic, Gerbers, PCB design files, and links for kits and bare PCBs; an assembled version is not offered. It is intended for the SC706 Z80 CPU module and is not compatible with the SC730 CPU plus MMU module. JP1 controls Flash write protection.

Sources
Build itChecked Jul 24, 2026SC715 and SC729 Compact Flash Modulesby Small Computer Central

Adds CompactFlash storage to RC2014 and RCBus systems at I/O ports 0x10 through 0x17.

For this platform (bus/interface): Both layouts are fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. They occupy I/O ports 0x10 through 0x17 and are supported by the documented RomWBW configurations.

Both designs have schematics, Gerbers, PCB files, and kit or bare-PCB paths; assembled versions are not offered. Plain CP/M 2.2 can address the first 128MB and RomWBW up to 2GB. The maker recommends avoiding high-capacity, high-speed cards and documents a critical 5 V power issue with some visually identical CompactFlash adapters.

Sources
Build itChecked Jul 24, 2026SC716 Z80 SIO/2 Serial Moduleby Small Computer Central

Adds two clock-stable serial ports using a Z80 SIO/2.

For this platform (bus/interface): Fully supported on 80-pin RCBus. It works on the 60-pin Enhanced Bus, but mode 2 interrupt chaining needs wires between modules. It also works on the 40-pin Standard Bus with the same interrupt-wiring limitation and without the optional CLK2, TX2, and RX2 signals.

The project supplies a schematic, Gerbers, PCB design files, and links for kits and bare PCBs; an assembled version is not offered. The full interrupt daisy chain and optional bus signals require the 80-pin RCBus or additional wiring as documented.

Sources
Build itChecked Jul 24, 2026SC717 Z80 PIO Moduleby Small Computer Central

Adds 16 programmable parallel I/O lines and four handshake lines through a Z80 PIO.

For this platform (bus/interface): Fully supported on 80-pin RCBus. It works on 40-pin Standard and 60-pin Enhanced backplanes, but a mode 2 interrupt chain requires wires between modules.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. On PCB v1.0.0, JP2 and JP3 are tight against the P2 box header; the assembly guide recommends filing a little plastic from those headers before soldering.

Sources
Build itChecked Jul 24, 2026SC718 Z80 CTC Moduleby Small Computer Central

Adds four programmable counter and timer channels with frequency and interrupt generation.

For this platform (bus/interface): Fully supported on 80-pin RCBus. It works on the 60-pin Enhanced Bus with added interrupt-chain wiring. On the 40-pin Standard Bus, interrupt wiring is also required and optional CLK2 and /INT2 signals are unavailable.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. The optional onboard oscillator is not included in the kit. Mode 2 interrupt chaining needs suitable backplane support or flying leads.

Sources
Build itChecked Jul 24, 2026SC719 Digital I/O Moduleby Small Computer Central

Adds eight 5 V TTL inputs and eight 5 V TTL outputs with state LEDs.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. Configure its single I/O address to avoid conflicts; 0x00 is the documented default.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. PCB v1.0.0 leaves insufficient space for C5 to sit tight against the board; this is fixed in PCB v1.0.1.

Sources
Build itChecked Jul 24, 2026SC721 Linear Memory Moduleby Small Computer Central

Adds 512K of RAM and selectable 512K Flash ROM to a 20-bit-address RCBus system.

For this platform (bus/interface): Requires a full 80-pin RCBus backplane because 40-pin Standard and 60-pin Enhanced buses do not carry address lines A16 through A19. Pair it with SC722 or SC730; it is not compatible with the SC706 CPU module.

The project provides Z80 and Z180 firmware, a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. Observe the Flash write-protect jumper and select the ROM/RAM arrangement required by the processor and firmware.

Sources
Build itChecked Jul 24, 2026SC722 Z180 CPU Moduleby Small Computer Central

Adds an 18.432 MHz Z180 processor, dual serial ports, and a microSD interface.

For this platform (bus/interface): Requires a full 80-pin RCBus backplane. The 40-pin Standard and 60-pin Enhanced buses do not provide address lines A16 through A19. SC721 is the recommended memory module.

The project provides firmware, a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. RomWBW supports the microSD interface, while the documented Small Computer Monitor configuration does not. On PCB v1.0.0 the JP2 RX2 and TX2 labels are swapped; v1.0.1 corrects them.

Sources
Build itChecked Jul 24, 2026SC725 Serial and Timer Moduleby Small Computer Central

Combines two Z80 SIO/2 serial ports with four programmable Z80 CTC channels.

For this platform (bus/interface): Fully supported on 80-pin RCBus. It works on the 60-pin Enhanced Bus with added mode 2 interrupt-chain wiring. The 40-pin Standard Bus needs the same wiring and lacks optional CLK2, TX2, and RX2 signals.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. The optional oscillator is not included in the kit. Standard RomWBW does not enable CTC support, so its documented jumper setup bypasses the CTC and assumes a 7.3728 MHz CPU clock.

Sources
Build itChecked Jul 24, 2026SC726 Clock Moduleby Small Computer Central

Generates three independently selected clock outputs for RCBus processor and peripheral timing.

For this platform (bus/interface): Fully supported on 80-pin RCBus. The 60-pin Enhanced Bus normally lacks optional CLK4, while the 40-pin Standard Bus lacks CLK2 and CLK4; the main CLK output remains available.

The project provides a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. Check every destination jumper to avoid driving a bus clock signal from more than one source.

Sources
Build itChecked Jul 24, 2026SC727 DS1302 Real-Time Clock Moduleby Small Computer Central

Adds a battery-backed DS1302 real-time clock and several spare I/O bits.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. Match the configurable I/O address to the selected firmware.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. The clock is supported by RomWBW but not by plain CP/M 2.2 or Small Computer Monitor. Writes to spare output bits require care because the port is shared with the RTC control bits.

Sources
Build itChecked Jul 24, 2026SC730 Z80 CPU plus MMU Moduleby Small Computer Central

Combines a Z80 processor with a 20-bit MMU for SC721's 1 MB linear memory.

For this platform (bus/interface): Requires a full 80-pin RCBus backplane. The 40-pin Standard and 60-pin Enhanced buses do not provide address lines A16 through A19, so the MMU and SC721 pairing cannot operate there.

The project provides firmware, a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. Pair it with SC721 linear memory and do not combine it with the bank-switching SC707 or SC714 memory modules.

Sources
Build itChecked Jul 24, 2026SC731 Dual PWM Moduleby Small Computer Central

Adds two independently writable pulse-width modulation outputs.

For this platform (bus/interface): Fully supported on 80-pin RCBus. It works on the 60-pin Enhanced Bus, but CLK4 is usually unavailable. On the 40-pin Standard Bus, optional CLK2 and CLK4 signals are unavailable; the direct PWM headers remain usable.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. The base address must be even; 0x04 is the documented example. Pulse frequency is the selected clock divided by 128.

Sources
Build itChecked Jul 24, 2026SC732 Dual Servo Moduleby Small Computer Central

Controls two hobby servos through two tightly decoded output ports.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. Choose an even base address that does not conflict with another write device.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. Although the servos can use the computer's 5 V rail, the maker strongly recommends an external supply because of loading and electrical-noise concerns.

Sources
Build itChecked Jul 24, 2026SC734 MicroSD Moduleby Small Computer Central

Adds simple bit-banged microSD storage with RomWBW support.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus. Configure its port as 0x69 for the documented RomWBW setup.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. Support is included in RomWBW v3.5; RomWBW v3.4 needs SDENABLE enabled in the RCBus_std configuration. Small Computer Monitor does not support it.

Sources
Build itChecked Jul 24, 2026SC737 50 Hz Interrupt Moduleby Small Computer Central

Adds a software-enabled 50 Hz system tick interrupt.

For this platform (bus/interface): Fully supported on 80-pin RCBus. It also works on 40-pin Standard and 60-pin Enhanced backplanes, but their optional /INT2 signal is unavailable; use /INT or /INT1 instead.

The project supplies a schematic, Gerbers, PCB design files, and kit or bare-PCB paths. Interrupt generation is disabled at reset. A jumper routes the signal to /INT, /INT1, or /INT2 where the chosen bus exposes it.

Sources
Build itChecked Jul 24, 2026SC738 Reset Moduleby Small Computer Central

Adds supervised power-on reset, a debounced reset button, and software-triggered reset.

For this platform (bus/interface): Fully supported on the 40-pin RC2014 Standard Bus, 60-pin RC2014 Enhanced Bus, and 80-pin RCBus.

The project provides a schematic, Gerbers, PCB design files, and kit or bare-PCB suppliers; an assembled version is not offered. Enable only one voltage supervisor in a system and choose an I/O address that does not conflict with another module.

Sources
AvailableChecked Jul 25, 2026Sergey Z80 CPU and 512K Memory Module Familyby Sergey Kiselev / Weird Electronics

Combines a Z80 CPU, 512 KiB Flash, 512 KiB SRAM, clock, reset, and RomWBW paging on one modular card.

For this platform (bus/interface): Both repositories explicitly state RCBus and RC2014 compatibility. Do not combine these cards with other active CPU, main-memory, clock, or reset modules. A serial module is required for the documented minimal RomWBW system; CompactFlash storage is optional.

Tindie listed the complete Z80-512K kit without an out-of-stock notice on 2026-07-25; complete open files also remain available for both designs. The Z80-CPM store page failed extraction, so no stock claim is made for that variant. Z80-512K builders using its supervisor without a backup battery must short the battery connector as documented.

Sources
AvailableChecked Jul 24, 2026SID-Ulator Sound Moduleby Z80 Kits

Adds an onboard emulation of the MOS 6581 or 8580 SID sound chip.

For this platform (stated family): A Standard Bus module designed for direct BASIC or assembly programming. It can reproduce SID-like sounds, but C64 SID files contain 6502 code and are not directly playable on an RC2014.

Surface-mount parts arrive assembled, programmed, and tested; the builder completes the through-hole kit. The default is 8580 emulation, changed to 6581 with a solder bridge. Paddle inputs and the SID voice-3 read registers are not emulated, and a decorative DIP28 chip is not included.

Sources
AvailableChecked Jul 24, 2026SIO/2 Dual Serial Moduleby Z80 Kits

Adds two Zilog SIO/2 serial ports for terminals, printers, and other devices.

For this platform (stated family): Supplied in Pro, Zed, and Zed Pro systems. It can replace a Classic II serial module only with an updated ROM. Lower Port B baud rates require a separate clock on CLK2.

Current kits are offered for Standard or Enhanced Bus. The Standard version includes a 20-pin header exposing CLK2, TX2, and RX2. Jumpers can allow either FTDI connection to power the RC2014.

Sources
Build itChecked Jul 25, 2026Tiny Z80by Sergey Kiselev

Business-card-sized RC2014-compatible Z80 computer with 1 MiB of memory and integrated serial and parallel I/O.

For this platform (bus/interface): The repository explicitly identifies the bus as RC2014 compatible. Treat Tiny Z80 as the system core and avoid duplicate CPU, memory, clock, reset, serial, or parallel functions. RomWBW 3.0.1 or later is supported with the documented Easy Z80 configuration changes.

This is a surface-mount self-assembly project with KiCad, Gerber, CPLD, and firmware documentation. Programming its MAX7000AE CPLD requires the older Quartus II 13.0sp1 toolchain because newer Quartus versions do not support the device.

Sources
AvailableChecked Jul 24, 2026Tynemouth 68B50 Clocked Serial Portby Tynemouth Software

Adds a 5 V TTL serial port and an independently usable 7.3728 MHz clock.

For this platform (bus/interface): The vendor explicitly describes RC2014 use as a replacement serial and clock module. It was originally designed for the Minstrel 4th, which is outside this record's compatibility attachment.

The current product is a through-hole kit, with a bare PCB also listed elsewhere. It normally replaces an existing 68B50 or SIO/2 module; using it alongside another serial port requires backplane modifications.

Sources
AvailableChecked Jul 24, 2026Tynemouth Joystick Moduleby Tynemouth Software

Adds one Atari and Commodore-style nine-pin joystick port.

For this platform (bus/interface): Designed as a Standard Bus RC2014 module. The maker also names Minstrel 4th and Minstrel 4D systems, but this catalog record attaches it only to the RC2014 family.

The current listing is a kit or bare-PCB design. The RC2014 computer and joystick shown in vendor photos are not included.

Sources
AvailableChecked Jul 24, 2026Universal Front Panel I/O Kitby Z80 Kits

Adds eight remote input switches and eight output LEDs for RomWBW or an Orton 3C.

For this platform (stated family): For RomWBW, the vendor names RC2014 Zed, Zed Pro, or another RC2014 fitted with the 512K ROM 512K RAM Module. It can also provide front-panel I/O to an Orton 3C fitted with a backplane.

The current kit has different LED, bezel, and resistor options for RomWBW systems and the Orton 3C. The bus-extension socket carries Standard Bus signals and up to four Enhanced Bus signals but is supplied unpopulated.

Sources
AvailableChecked Jul 24, 2026Why Em-Ulator Sound Moduleby Z80 Kits

Emulates a YM2149, AY-3-8910, or AY-3-8912 without requiring an original sound chip.

For this platform (bus/interface): A Standard Bus sound module. Use 0xD8/0xD0 for the documented RC2014 and RomWBW software or switch to 0xA0/0xA1 for compatible MSX ports.

Current kits select an emulated chip and clock frequency. The module supports the RomWBW PLAYER program and existing BASIC examples, but does not emulate the original chips' GPIO ports. A cosmetic DIP40 cover is optional.

Sources
AvailableChecked Jul 24, 2026YM2149 Sound Cardby Ed Brindley

Adds three-channel YM2149 or AY-3-8910 sound and stereo line output to an RC2014.

For this platform (stated family): The project documents operation in a standard RC2014 setup and RomWBW support. Its base I/O address is jumper-selectable from 0x00 through 0xF0 in 0x10 steps, or it can use ZX Spectrum-style 16-bit addressing. Clock jumpers select the bus or onboard oscillator and divide the clock to stay within the AY chip's limit.

The current Z80 Kits version is sold without a YM or AY sound chip because those parts are no longer manufactured. The builder must obtain a suitable chip. An optional ZXTT module supplies a 1.7734 MHz clock.

Sources
AvailableChecked Jul 24, 2026Z80 CPU Moduleby Z80 Kits

Provides a replaceable Z80 processor module with optional advanced bus signals.

For this platform (stated family): Supplied in Pro, Zed, and Zed Pro and sold as a replacement for Classic II or for custom builds. Compatible with Standard and Enhanced Bus backplanes using the selected header option.

The current kit does not include a ZIF socket. On the Standard Bus option, a separate ten-pin header exposes /NMI, /WAIT, /BUSRQ, and /BUSACK.

Sources