Tag: analog rgb

Converts Commodore 128 80-column RGBI into 15 kHz analog RGB for a compatible display or a separate VGA scaler.

The official site says sales resumed through its Square store in January 2024, but current stock was not independently confirmed on 2026-07-30. BIT-C-128 is not a scan converter: direct use requires a display that accepts roughly 15.75 kHz analog RGB. An ordinary VGA display also needs a GBS-8200, GBS-8220, or another suitable scaler. Supply regulated 5 V power and the cables or adapters required by the selected display path.

Converts the C128's 80-column digital RGBI output to analog RGB and composite sync for a separate video scaler.

Protovision reported eight units in stock at EUR 30 on 2026-07-30. This adapter converts signal levels and combines sync but does not raise the scan rate. Its documented setup uses a separate GBS-8200 or GBS-8220, which is not included. Follow the page's normal/inverted-sync procedure if GBS auto scan does not lock cleanly.

A passive buildable adapter that converts C128 80-column RGBI to 15 kHz analog RGB and adds monochrome composite output.

The repository publishes KiCad schematic and board files plus Gerbers. This is not a scan doubler or scaler, so the connected display must accept 15 kHz analog RGB with separate 5 V horizontal and vertical sync. The design has no CGA brown fix, does not provide VGA identification or communication signals, and will not work with a downstream converter that requires composite sync. The maker reports a successful Dell 27-inch monitor test but calls the test computer a 'C128cr'; do not infer separate C128D or C128DCR testing from that ambiguous label.

Combines a Commodore 128's 40-column and 80-column video paths in one switchable external adapter.

Pyrofer's Projects lists the NTSC board and its separate C128DCR mounting tab as out of stock. The normal package uses tabs for the flat C128 and standard C128D; the differently spaced C128DCR requires the separate tab. Although the board has a PAL/NTSC selection, the seller says changing format also requires a different oscillator IC, and the listed package includes the NTSC oscillator.

Converts digital RGBI into 15 kHz analog RGB and can break out a Commodore 128's 40-column S-Video and audio.

The maker lists the assembled board as out of stock and publishes no fabrication package. This is not a scan converter; the display must accept the source timing, normally about 15 kHz, or use a separate scaler. The maker's design history says the completed logic omits the valid intensity-only dark-gray color, which appears black. The board also passes 5 V to HD-15 pin 9; verify that the attached cable and display do not ground that pin.

Converts MDA, CGA, EGA, and Commodore 128 RGBI into 15 kHz analog RGB with selectable sync.

The maker labels the current project revision released, but its assembled Tindie listing said the seller was taking a break on 2026-07-30. The maker publishes a schematic but not a complete fabrication package. This is not a scan converter: an ordinary VGA display needs a GBS-8200, GBS-8220, OSSC, or another compatible scaler. The board requires 5 V through Micro-USB or a suitable GBS power connection.

A simple buildable RGBI-to-analog-RGB adapter for 15 kHz-capable displays with a VGA connector.

The PCBWay project supplies a shared board-order path and a short component list. Assembly is required. This is explicitly not a scan doubler, so most ordinary VGA displays will not work; verify that the exact monitor accepts 15 kHz analog RGB. The maker reports a successful test with a flat Commodore 128 and an Acer G206HQL, but does not separately document C128D or C128DCR testing.

A buildable C128 and IBM CGA digital-to-analog video adapter with RGBS, RGBHV, and Commodore A/V pass-through options.

The repository publishes KiCad sources, Gerbers, a BOM, and printable cases for revision 1.3. The maker tested RGBI, composite, S-Video, audio, and GBS-Control output; revision 1.3 corrects the earlier monochrome pass-through error. This is not a scan converter. Use a compatible 15 kHz path such as GBS-Control or a suitable SCART converter. Never connect the C128 A/V power input and the external barrel power input at the same time. The maker found an ordinary SCART-to-HDMI box unstable in one 80-column game while GBS-Control remained stable.